loading spinner

Home

Home

Left Banner

List of products by brand White Peaks

  • CopraDur

    €32.31

    Splint

    Blank of high-quality, highly crosslinked polyamide. CopraDur is practically unbreakable and therefore suitable for the fabrication of orthodontic splints with only 0,5mm thickness. It stays very flexible and provides a very smooth, gliding surface for optimum patient comfort.

  • CopraEasyMill NP

    €140.00

    Isostatic, powder-metallurgical manufactured hard Co/Cr blank

    Optimum homogeneity due to isostatic high pressure manufacturing process. Minimal bur wear out due to extremely high homogeneity without “hard islands” and casting segregations as with common Co/Cr blanks. Higher milling speed due to better machinability (like titanium) and lower Vickers hardness. Up to 50% shorter process time in your milling system.

  • Copran® Zri | Copran® Zri...

    €93.85

    Classic zirconia with highest bending strength (1400 MPa) for bridges with up to 14 pontics

  • Copran® Zri | Copran® Zri...

    €93.85

    Classic Zirconia Blank with highest bending strength (1400 MPa) for bridges with up to 14 pontics

  • CopraPeek

    €121.54

    Light / Medium / Rose / Bio Classic

    The very high biocompatibility of this high tech resin makes it the first choice for prosthetic bases, primary-, secondary- and tertiary constructions, metal free supra-structures as well as crown and bridge restorations. CopraPeek provides best comfort for the patient due to its minimal weight and extreme low thermal conductivity. Available in dentin A2 like shade “Medium”, “Light” grey, gum shade “Rose” and natural/not coloured “Bio Classic. CopraPeek is very plaque resistant, non-allergenic and tasteless.

  • CopraSintec Evo K

    €130.00

    World´s first “middle-soft” milling of Co/Cr in 98mm – wet or dry! The blank is pre-sintered, so most delicate structures and minimal wall thicknesses can be realized. The blank does not contain binder anymore, so the sintering time is greatly reduced, resulting in less argon gas consumption. Also manufactured in isostatic high pressure process, same indications as the softer CopraSintec K. Very small wear of burs.

  • CopraSintec K

    €122.86

    Soft as wax milling of Co/Cr – wet or dry! The isostatic high pressure manufacturing process allows bridges with up to 14 units and even implant bar restorations. Non precious metal alloy type 4, therefore no limitations compared to milled or cast Co/Cr alloys. The small shrinkage allows you to place up to 40 units in a blank. Minimal wear of burs.

  • CopraSmile Symphony |High...

    €127.14

    9-layer (5 layers plus 4 transition layers) zirconia with highest translucency for anterior- or posterior restorations with up to 3 units. In the production process, 5 layers of pre-coloured zirconia are layered on top of each other, building 4 transition layers in the process. The result is an extremely natural colour transition for vivid, lively restorations. Bending strength about 600 Mpa

  • CopraSmile | CopraSmile...

    €109.23

    Cubic, isostatically pressed zirconia with highest translucency for anterior- or posterior restorations with up to 3 units. Bending strength about 600 Mpa

  • CopraSmile | CopraSmile...

    €109.23

    Cubic, isostatically pressed zirconia with highest translucency for anterior- or posterior restorations with up to 3 units. Bending strength about 600 Mpa.

  • CopraSupreme Hyperion

    €167.14

    multidimension, 9-layer, high translucent zirconia. the production process, 5 different layers of pre-coloured Tosoh zirconia powders of different bending strength (≥ 600-1100 MPa) are layered on top of each other, building 4 transition layers in the process.

    The result is an extremely natural colour transition for vivid, lively restorations for up to 14 units.

  • CopraSupreme Symphony

    €127.14

    9-layer (5 layers plus 4 transition layers), tanslucent zirconia with high translucency and higher bending strength (about 1100 Mpa) for copings and fully anatomical restorations for up to 14 units. In the production process, 5 layers of pre-coloured zirconia are layered on top of each other, building 4 transition layers in the process. The result is an extremely natural colour transition for vivid, lively restorations.